锐捷s6000交换机怎么实现堆叠
答案:1 悬赏:0
解决时间 2021-01-11 17:54
- 提问者网友:伴风望海
- 2021-01-11 13:02
锐捷s6000交换机怎么实现堆叠
最佳答案
- 二级知识专家网友:鱼忧
- 2021-01-11 14:28
这是一款数据中心交换机,本身支持虚拟化,也就是VSU.配置参考
核心交换机1:
Switch1# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch1(config)# switch virtual domain 1
Switch1(config-vs-domain)# switch 1
Switch1(config-vs-domain)# switch 1 priority 200 ------>默认优先级为100,配置为较高的优先级,VSU建立成功后将会成为管理主机。
Switch1(config-vs-domain)# exit
Switch1(config)# vsl-aggregateport 1 ------>VSL链路至少需要2条,一条链路可靠性较低,当出现链路震荡时,VSU会非常不稳定。
Switch1(config-vsl-ap-1)# port-member interface TenGigabitEthernet 1/1------>配置VSL链路,VSU主备核心之间的心跳链路和流量通道
Switch1(config-vsl-ap-1)# port-member interface TenGigabitEthernet 1/2
Switch1(config-vsl-ap-1)# exit
核心交换机2:
Switch2# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch2(config)# switch virtual domain 1------>domaind id 必须和第一台一致
Switch2(config-vs-domain)# switch 2 ------>第二台设备必须更改ID为2
Switch2(config-vs-domain)# switch 2 priority 150
Switch2(config-vs-domain)# exit
Switch2(config)# vsl-aggregateport 1------>VSL链路至少需要2条,一条链路可靠性较低,当出现链路震荡时,VSU会非常不稳定。
Switch2(config-vsl-ap-1)# port-member interface TenGigabitEtherne 1/1------>配置VSL链路,VSU主备核心之间的心跳链路和流量通道
Switch2(config-vsl-ap-1)# port-member interface TenGigabitEthernet 1/2
Switch2(config-vsl-ap-1)# exit
核心交换机1:
Switch1# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch1(config)# switch virtual domain 1
Switch1(config-vs-domain)# switch 1
Switch1(config-vs-domain)# switch 1 priority 200 ------>默认优先级为100,配置为较高的优先级,VSU建立成功后将会成为管理主机。
Switch1(config-vs-domain)# exit
Switch1(config)# vsl-aggregateport 1 ------>VSL链路至少需要2条,一条链路可靠性较低,当出现链路震荡时,VSU会非常不稳定。
Switch1(config-vsl-ap-1)# port-member interface TenGigabitEthernet 1/1------>配置VSL链路,VSU主备核心之间的心跳链路和流量通道
Switch1(config-vsl-ap-1)# port-member interface TenGigabitEthernet 1/2
Switch1(config-vsl-ap-1)# exit
核心交换机2:
Switch2# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch2(config)# switch virtual domain 1------>domaind id 必须和第一台一致
Switch2(config-vs-domain)# switch 2 ------>第二台设备必须更改ID为2
Switch2(config-vs-domain)# switch 2 priority 150
Switch2(config-vs-domain)# exit
Switch2(config)# vsl-aggregateport 1------>VSL链路至少需要2条,一条链路可靠性较低,当出现链路震荡时,VSU会非常不稳定。
Switch2(config-vsl-ap-1)# port-member interface TenGigabitEtherne 1/1------>配置VSL链路,VSU主备核心之间的心跳链路和流量通道
Switch2(config-vsl-ap-1)# port-member interface TenGigabitEthernet 1/2
Switch2(config-vsl-ap-1)# exit
我要举报
如以上问答内容为低俗、色情、不良、暴力、侵权、涉及违法等信息,可以点下面链接进行举报!
大家都在看
推荐资讯